Results 1 to 10 of 10

Thread: Weco Edge 430 problem - need help!

  1. #1
    OptiBoard Novice
    Join Date
    Jul 2012
    Location
    Serbia
    Occupation
    Ophthalmologist
    Posts
    2

    Confused Weco Edge 430 problem - need help!

    I have problem with this device, when hi finish frst round of cuting class after measuring work on display shows a massage:

    Rear surface convex:
    measurement inaocurate?

    i=35 dz=2.21

    confirm with (Enter)


    after I press enter it shows another error:

    Error

    Nummer: 1407

    Steuerung ist nich bereit.
    Programmstart nicht moglich.
    Z_ZST_WAIT_Z_ZPOS_RUN_E


    thas anibody know how to solve this problem?

    thanks,

  2. #2
    OptiWizard
    Join Date
    Feb 2010
    Location
    ALBUQUERQUE
    Occupation
    Optical Wholesale Lab (other positions)
    Posts
    328
    Is this an isolated error or is it occurring on all jobs? The key to the error is the dz 2.21. The right side chuck measures the center thickness to determine bevel placement. If the lens is too thin..then the error will occur. Caliper the lens to verify minimum of 2.2. As a result the next error occurs. Z is the frame profile or bevel placement measured during the roughing cycle. If thickness is off the z set cannot be calculated.

  3. #3
    OptiBoard Novice
    Join Date
    Jul 2012
    Location
    Serbia
    Occupation
    Ophthalmologist
    Posts
    2
    Quote Originally Posted by PRECISIONLAB View Post
    Is this an isolated error or is it occurring on all jobs? The key to the error is the dz 2.21. The right side chuck measures the center thickness to determine bevel placement. If the lens is too thin..then the error will occur. Caliper the lens to verify minimum of 2.2. As a result the next error occurs. Z is the frame profile or bevel placement measured during the roughing cycle. If thickness is off the z set cannot be calculated.
    Its error on all jobs, problem is that in Serbia there is no service for this machines :(

  4. #4
    OptiWizard
    Join Date
    Feb 2010
    Location
    ALBUQUERQUE
    Occupation
    Optical Wholesale Lab (other positions)
    Posts
    328
    Try running a relatively thick or strong plus lens. Watch to make sure the guides on either side of the roughing wheel make contact with the lens edge. If the error persist you may need to calibrate right side chuck position. If possible post picture of your machine

  5. #5
    OptiBoard Apprentice
    Join Date
    Jan 2006
    Location
    Netherlands
    Occupation
    Other Optical Manufacturer or Vendor
    Posts
    28
    If the problem still exists. mail me

  6. #6
    OptiBoard Novice
    Join Date
    Mar 2018
    Location
    Egypt
    Occupation
    Other Eyecare-Related Field
    Posts
    9
    I have another problem with the same type WECO 430 Edge

    When the machine starts it does`t complete the starting test and have an error message:

    Error no.: 11005
    positiver hardware-Endschalter aktiv
    X

    this is the message displayed on the screen.
    i hope there are a help for this problem .
    Also i hope anybody can help me with the manual of this machine specially MAINTENANCE MANUAL.

    Regards

  7. #7
    OptiWizard
    Join Date
    Feb 2010
    Location
    ALBUQUERQUE
    Occupation
    Optical Wholesale Lab (other positions)
    Posts
    328
    The error refers to a limit switch not triggering during a set time. The X refers to machines X axis which I believe is movement left to right. Y would be front to back. Check to make sure there isn't any swarf behind grinding wheels which might be limiting movement. Next step is to check internal gear and rails the wheel assembly sits on. During startup manually assist the movement to the achieve max distance within grinding chamber

  8. #8
    OptiBoard Novice
    Join Date
    Mar 2018
    Location
    Egypt
    Occupation
    Other Eyecare-Related Field
    Posts
    9
    Thanks alot for your fast replay, but i already change the limit from x to y then to z (which is responsible for the lens motor) i notice that on start up the motor did not stop so i change the limit with another one with the same specification but there are a vibration noticed on the y axis i don not knew what is the relation between the limit abd the vibration so what do you think.

  9. #9
    OptiBoard Novice
    Join Date
    Mar 2018
    Location
    Egypt
    Occupation
    Other Eyecare-Related Field
    Posts
    9
    I need weco 430 edge manual in english can anybody help me with a soft copy for it.

  10. #10
    OptiBoard Novice
    Join Date
    Mar 2018
    Location
    Egypt
    Occupation
    Other Eyecare-Related Field
    Posts
    9
    I have weco 430 edge and have the following message after i translate it to english.

    2700
    Time out at exact stop with following error monitoring:
    %9200 N50/5 Axe2

    Can you help me with this error message please.

    I need a wecco 430 edge manual as soon as possible if some one can help me with that too ��
    Last edited by Agoumaa; 03-13-2018 at 08:39 PM.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Problems with Weco Edge 430
    By Win C in forum General Optics and Eyecare Discussion Forum
    Replies: 3
    Last Post: 03-13-2018, 08:36 PM
  2. Weco CAD 2 and Weco Form Tracer
    By Ocular Dexter in forum Optical Marketplace
    Replies: 7
    Last Post: 11-04-2012, 01:07 PM
  3. How long does it take to edge a job?
    By ilanh in forum General Optics and Eyecare Discussion Forum
    Replies: 67
    Last Post: 12-19-2009, 02:56 PM
  4. Weco Edge 230 you name the price
    By beyeker in forum Optical Marketplace
    Replies: 2
    Last Post: 07-03-2009, 07:22 PM
  5. Edge Thickness
    By Ned in forum General Optics and Eyecare Discussion Forum
    Replies: 0
    Last Post: 10-30-2008, 04:52 AM

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
OptiBoard is proudly sponsored by:
BC College of Optics, Younger Optics and Vision Equipment