Results 1 to 18 of 18

Thread: Formula for calculating thicknesses

  1. #1
    Bad address email on file Spex's Avatar
    Join Date
    Jul 2000
    Location
    Richmond, Va USA
    Occupation
    Dispensing Optician
    Posts
    46

    Post

    Does anyone have a formula for calculating center & edge thicknesses that takes into account lens material, lens power, frame specs, PD, etc.?

    I am really looking for some software to do this but if I could get an accurate formula I maybe able to create a spreadsheet or basic program to do the calculations.

    Thanks!

  2. #2
    Master OptiBoarder OptiBoard Gold Supporter Judy Canty's Avatar
    Join Date
    May 2000
    Location
    Virginia Beach, VA
    Occupation
    Dispensing Optician
    Posts
    7,482

    Redhot Jumper

    Your best reference is the Optical Formulas Tutorial by Ellen Stoner and Patricia Perkins. It's a softcover book, not terribly expensive and one of the best I've used.

  3. #3
    sub specie aeternitatis Pete Hanlin's Avatar
    Join Date
    May 2000
    Location
    Hickory Creek, TX
    Occupation
    Lens Manufacturer
    Posts
    4,964

    Post

    If it is software you seek, check out the downloadable programs section of the OptiBoard. Our very own Darryl Meister has written a spreadsheet called "OpticsLite" that performs the calculations you require (and many more).

    Otherwise, I believe you will need to calculate the sagittal depth of each surface of whatever lens you wish to estimate the thickness of and go from there. Part of calculation of sagittal depth will take into account the amount of decentration (to determine the diameter of the lens).

    A somewhat more simplistic way of calculating thickness (which I use from time to time) is to actually DRAW the lens on paper. I calculate the radius of curvature for each surface, consider the minimum thickness I desire, and draw the lens using a compass (I have some templates for the flatter curves already made)- generally works pretty well for demonstration/estimation purposes.

    Pete

  4. #4
    Master OptiBoarder Darryl Meister's Avatar
    Join Date
    May 2000
    Location
    Kansas City, Kansas, United States
    Occupation
    Lens Manufacturer
    Posts
    3,700

    Post

    I wrote an article for calculating lens thickness that is now in the OptiBoard archives, which you might also find useful.

    Best regards,
    Darryl

  5. #5
    Bad address email on file Spex's Avatar
    Join Date
    Jul 2000
    Location
    Richmond, Va USA
    Occupation
    Dispensing Optician
    Posts
    46
    Thanks Judy, Pete, & Darryl for your suggestions. They are great.

    Pete, what if you can't draw. But I may try your suggestion for demo purposes with customers.

    Judy, I have located one of my optical books buried deep in my basement. It has a formula in it that I can use. But I would like to find a way to look at your book. I am going to call my local community college that has an opticians program & see if they have a copy I can look thru. I may still find it useful in the future.

    Darryl, I have your OpticsLite program & really like what you did. Is there anyway to incorporate a thickness calculator with in the Rx & Multifocal Analysis that would take into account lens material or index of refraction? That is a great interface you did inside Excel. I like it very much!

    I am experimenting with the formulae I have found within an Excel spreadsheet, & its working but I still think there are some factors missing. Like the sagittal depth mention by Pete. There is a formula in this book for that also. Now I just have to incorporate it within what I have.

    Thanks again guys & gals!!!
    Chris

  6. #6
    Master OptiBoarder Darryl Meister's Avatar
    Join Date
    May 2000
    Location
    Kansas City, Kansas, United States
    Occupation
    Lens Manufacturer
    Posts
    3,700

    Post

    Hi Chris,

    Actually, within the Ray Tracing module the spreadsheet calculates lens edge thickness, center thickness, and weight for you -- by material. You just dial in the Rx, the minimum blank size of the frame, and select a lens material. You can also choose a base curve and some other stuff, if you want to get terribly accurate. By toggling the lens view button, it also shows you a cross-section of your lens -- so that you have an actual picture to look at.

    Best regards,
    Darryl

  7. #7
    Bad address email on file Spex's Avatar
    Join Date
    Jul 2000
    Location
    Richmond, Va USA
    Occupation
    Dispensing Optician
    Posts
    46
    Hey Darryl, I see what you mean. It looks like this is what I was looking for. And it even gives you a graphic drawing of the lens thickness. That's great!!

    Do I need to do anything else other than enter the lens information like choose the material, lens power, base curve, center thinkness (on + edge thickness), & lens diameter to come up with the correct edge (or center) thickness?
    You don't need to enter anything like the pupil size, vertex distance, angle of view, etc., do you?
    And what effect does the Asphere P-Value have on thickness?

    Thanks again for letting me know about that. I think I will put my little attempt on hold & just refer to your program. I keep finding out that program does more & more. I am going to start using it more. Thanks very much for taking the time to produce it! I believe it was time well spent!

  8. #8
    Master OptiBoarder Darryl Meister's Avatar
    Join Date
    May 2000
    Location
    Kansas City, Kansas, United States
    Occupation
    Lens Manufacturer
    Posts
    3,700

    Post

    Hi Chris,

    You can adjust things like the vertex distance and angle of view to examine the peripheral performance of the lens. The calculations for unwanted oblique astigmatism, power error, and distortion are computed for whatever angle of view you pick. (A reference angle of 30 degrees is generally chosen in lens design work.) You'll notice, for instance, that you can control the peripheral performance by changing the base curve. You can design a "best form" lens, for example, by choosing the base curve that minimizes the unwanted lens aberrations I mentioned earlier.

    I would just leave "pupil size" alone. It's just for some more advanced and esoteric features that you probably won't need.

    The p-value allows you to incorporate simple asphericity into the lens design. Leave it at 1 for spherical base curves. For plus-powered lenses that use flatter than best form base curves, use a p-value below 1. For flattened minus-powered lenses, choose a p-value above 1. Simply adjust the p-value (up or down) until the lens aberrations are minimized.

    Best regards,
    Darryl

  9. #9
    OptiBoard Novice
    Join Date
    May 2000
    Location
    Lier Belgium
    Occupation
    Optometrist
    Posts
    9

    Post

    Originally posted by Judy Canty:
    Your best reference is the Optical Formulas Tutorial by Ellen Stoner and Patricia Perkins. It's a softcover book, not terribly expensive and one of the best I've used.
    what is the isbn number???

  10. #10
    OptiBoard Novice
    Join Date
    May 2000
    Location
    Lier Belgium
    Occupation
    Optometrist
    Posts
    9

    Post

    Originally posted by Darryl Meister:
    Hi Chris,

    Actually, within the Ray Tracing module the spreadsheet calculates lens edge thickness, center thickness, and weight for you -- by material. You just dial in the Rx, the minimum blank size of the frame, and select a lens material. You can also choose a base curve and some other stuff, if you want to get terribly accurate. By toggling the lens view button, it also shows you a cross-section of your lens -- so that you have an actual picture to look at.

    Best regards,
    Darryl
    Can you give some more info on the Ray Tracing module??
    Where can we get it??
    is it also available in Europe?

    Thanks Achilles




    ------------------

  11. #11
    Forever Liz's Dad Steve Machol's Avatar
    Join Date
    Apr 2000
    Location
    Back in AZ
    Occupation
    Other Eyecare-Related Field
    Posts
    10,243

    Post

    Originally posted by achilles:
    <FONT COLOR=#FF0000> Can you give some more info on the Ray Tracing module??
    Where can we get it??
    is it also available in Europe?

    Thanks Achilles
    </FONT>
    Actually it's available right here in the OptiBoard Download directory. You'll need Microsoft Excel to run it. Here's the link:

    Optics Lite



    ------------------

    OptiBoard Administrator

  12. #12
    Master OptiBoarder OptiBoard Gold Supporter Judy Canty's Avatar
    Join Date
    May 2000
    Location
    Virginia Beach, VA
    Occupation
    Dispensing Optician
    Posts
    7,482

    Redhot Jumper

    ISBN 0-7506-9913-2
    Optical Formulas Tutorial
    Ellen D. Stoner and Patricia Perkins
    Butterworth Heinemann Publishers

  13. #13
    OptiBoard Novice
    Join Date
    May 2000
    Location
    Lier Belgium
    Occupation
    Optometrist
    Posts
    9

    Post

    Thanks for your reply and help

    achilles


  14. #14
    OptiBoard Novice
    Join Date
    Aug 2016
    Location
    usa
    Occupation
    Dispensing Optician
    Posts
    1
    Quote Originally Posted by Steve Machol View Post
    Actually it's available right here in the OptiBoard Download directory. You'll need Microsoft Excel to run it. Here's the link:

    Optics Lite



    ------------------

    OptiBoard Administrator
    Where is the Optics Lite? The link does not work.

  15. #15
    OptiBoard Professional ThePinkRanger's Avatar
    Join Date
    May 2016
    Location
    Pittsfield, MA
    Occupation
    Dispensing Optician
    Posts
    103
    Quote Originally Posted by apurvadave View Post
    Where is the Optics Lite? The link does not work.
    That was posted originally 16 years ago, try this by Harry, it's amazing:

    https://makeoptics.com/harrychiling/.../calculators/2

  16. #16
    Ghost in the OptiMachine Quince's Avatar
    Join Date
    Jan 2016
    Location
    Sebago ME
    Occupation
    Optical Laboratory Technician
    Posts
    1,172
    Quote Originally Posted by ThePinkRanger View Post
    That was posted originally 16 years ago, try this by Harry, it's amazing:

    https://makeoptics.com/harrychiling/.../calculators/2

    This is awesome! I just got so lost in playing with this calculator. This stuff is the reason I joined Optiboard. Thank you geniuses
    Have I told you today how much I hate poly?

  17. #17
    OptiBoard Novice
    Join Date
    Sep 2016
    Location
    China
    Occupation
    Other Optical Manufacturer or Vendor
    Posts
    7
    Hi Darry

    Do your formula for both Positive and Negtive lens?

  18. #18
    OptiBoard Novice
    Join Date
    Sep 2017
    Location
    London
    Occupation
    Other Optical Manufacturer or Vendor
    Posts
    1
    Stoner & Perkins book for sure.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. lens thickness formula
    By hip chic in forum Ophthalmic Optics
    Replies: 29
    Last Post: 04-19-2010, 09:25 AM
  2. Fishin' for a Formula
    By Blake in forum Ophthalmic Optics
    Replies: 4
    Last Post: 07-24-2004, 11:45 AM
  3. toric formula
    By JJ in forum General Optics and Eyecare Discussion Forum
    Replies: 5
    Last Post: 07-08-2003, 10:32 PM
  4. Hi Index Lens Formula
    By SMW in forum General Optics and Eyecare Discussion Forum
    Replies: 5
    Last Post: 01-19-2003, 07:49 PM
  5. lens thickness formula
    By hip chic in forum Feedback, Comments and Help
    Replies: 1
    Last Post: 01-17-2001, 06:22 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •