Results 1 to 15 of 15

Thread: Code Error for Santinelli Edger 7070 3d

  1. #1
    Bad address email on file
    Join Date
    Jan 2006
    Location
    texas
    Occupation
    Dispensing Optician
    Posts
    21

    Wave Code Error for Santinelli Edger 7070 3d

    Can anyone tell me what the code error 008 is for the santanelli edger.
    We just recently purchased one without instructions. I have 2 Horizon II that are perfect and I have no problems with these.

    Does anyone have a copy?

    Any help would be so appreciated.

    thanks

  2. #2
    Software Engineer NetPriva.com mirage2k2's Avatar
    Join Date
    Nov 2005
    Location
    Australia
    Occupation
    Consumer or Non-Eyecare field
    Posts
    175
    saw an old post by igirl who was selling one - perhaps she can help.
    There are 10 kinds of people, those that understand binary, and those that don't!

  3. #3
    OptiBoardaholic Thumbs's Avatar
    Join Date
    Dec 2003
    Location
    US
    Occupation
    Dispensing Optician
    Posts
    231
    Why don't you call Sntanelli and ask?

  4. #4
    Software Engineer NetPriva.com mirage2k2's Avatar
    Join Date
    Nov 2005
    Location
    Australia
    Occupation
    Consumer or Non-Eyecare field
    Posts
    175
    There are 10 kinds of people, those that understand binary, and those that don't!

  5. #5
    Vision Equipment OptiBoard Corporate Sponsor Leo Hadley Jr's Avatar
    Join Date
    Mar 2003
    Location
    Florida
    Occupation
    Other Optical Manufacturer or Vendor
    Posts
    1,656
    Quote Originally Posted by Drod3210
    Can anyone tell me what the code error 008 is for the santanelli edger.
    We just recently purchased one without instructions. I have 2 Horizon II that are perfect and I have no problems with these.

    Does anyone have a copy?

    Any help would be so appreciated.

    thanks
    The Grinding pressure is not initialized, Check the origin sensor and cables which concern the grinding pressure motor.

    You can try to change your pressure from low to high or visa versa, that might be a quick fix.

    It is important that when you buy a used edger that you buy from a reputable company who can support what they sell. It might cost a little more but you will save thousands in the long run.
    Leo Hadley Jr
    Vision Equipment
    T: 855.776.2020

    www.visionequipmentinc.com

  6. #6
    Rising Star
    Join Date
    Aug 2004
    Location
    Colorado
    Occupation
    Frame Manufacturer
    Posts
    53

    That is an easy one.

    Code 800 means it is about to have a fatal error and that tech support is going to blow you off for a few days. After you call them a few dozen times they will eventually give you an answer. Good Luck.

    Buy Briot Axcell and smile

  7. #7
    Vision Equipment OptiBoard Corporate Sponsor Leo Hadley Jr's Avatar
    Join Date
    Mar 2003
    Location
    Florida
    Occupation
    Other Optical Manufacturer or Vendor
    Posts
    1,656
    Buy Briot Axcell and smile

    Nice edger to run but, Have you tried breaking one down yet??? Its not the easiest one to work on.
    Leo Hadley Jr
    Vision Equipment
    T: 855.776.2020

    www.visionequipmentinc.com

  8. #8
    Vision Equipment OptiBoard Corporate Sponsor Leo Hadley Jr's Avatar
    Join Date
    Mar 2003
    Location
    Florida
    Occupation
    Other Optical Manufacturer or Vendor
    Posts
    1,656
    I guess he fixed his error...............

    He never came back
    Leo Hadley Jr
    Vision Equipment
    T: 855.776.2020

    www.visionequipmentinc.com

  9. #9
    Rising Star
    Join Date
    Aug 2004
    Location
    Colorado
    Occupation
    Frame Manufacturer
    Posts
    53

    Yes I have.

    I have done a number of maintenace related things to the edger (this is the Accura CL that I have) and I have not had any problems at all. I think it is rather easy to get to things, flip the lid up and you can get to most of the things you need, and one side panel lets the whole pc board pivot down flat, If there was anything really major I just call John at JA Optronics and he will come fix it.

  10. #10
    Vision Equipment OptiBoard Corporate Sponsor Leo Hadley Jr's Avatar
    Join Date
    Mar 2003
    Location
    Florida
    Occupation
    Other Optical Manufacturer or Vendor
    Posts
    1,656
    Quote Originally Posted by beertv
    If there was anything really major I just call John at JA Optronics and he will come fix it.
    Thats kind of what I meant. When you have major problems "and you will", Its not that easy or inexpensive to fix. John obviously knows the machine well. I would much rather rebuild a Santinelli or Optronics edger than a Briot.
    Leo Hadley Jr
    Vision Equipment
    T: 855.776.2020

    www.visionequipmentinc.com

  11. #11
    Rising Star
    Join Date
    Aug 2004
    Location
    Colorado
    Occupation
    Frame Manufacturer
    Posts
    53

    repairs,

    Well we have a service contract and it is very reasonable and he comes down a few times a year and just makes sure everything is like it should be. He also provides updates to software and eproms and such. Even if we had to pay him out side of a service contract it is cheaper to pay him than for me to spend a day or two trying to do it myself. In most cases he can be in the office same day or next day. But service is key to any system you put in. I would not be opposed to buying a new Kappa or what ever else IF I knew I had really good in office support (read that fast to get there *** in my office) and they did not charge an arm and a leg to do it.

  12. #12
    Rising Star
    Join Date
    Nov 2003
    Location
    mass
    Occupation
    Dispensing Optician
    Posts
    151

    error code

    I think it means that the tracer is hitting the block or the blocking tape. On frames with a small B measurement you have to trim the blocking tape.

  13. #13
    Bad address email on file
    Join Date
    Jan 2006
    Location
    texas
    Occupation
    Dispensing Optician
    Posts
    21

    Your expertise never ceases to amaze me!!!!!!!

    thanks for all the help I will definately try to adjust the pressure. I am positive this will work. They are also sending my instructions I asked for.

    Your Are All Great Opticians.........Hats off to ya! Yeeee Haaaaaa;)

  14. #14
    Vision Equipment OptiBoard Corporate Sponsor Leo Hadley Jr's Avatar
    Join Date
    Mar 2003
    Location
    Florida
    Occupation
    Other Optical Manufacturer or Vendor
    Posts
    1,656
    Quote Originally Posted by Drod3210
    thanks for all the help I will definately try to adjust the pressure. I am positive this will work. They are also sending my instructions I asked for.

    Who is they? That error is definately coming from the grinding pressure switch. If adjusting the pressure does not work you can remove the cover and check the connection from the pressure switch to the small board next to the head motor. It may be a loose connection. If not, there is a broken connection in the switch, you could resolder the wires or get a new switch.

    Keep us updated!!!
    Leo Hadley Jr
    Vision Equipment
    T: 855.776.2020

    www.visionequipmentinc.com

  15. #15
    Bad address email on file
    Join Date
    Jan 2006
    Location
    texas
    Occupation
    Dispensing Optician
    Posts
    21

    Wave Thanks a Million

    I had purchased the machine on ebay so unfortunately it did not have the instructions that I needed. Like I said I am old lab rat I am used to the old Weco 440's and Gerber Corburn Ton generators. This one is new to me even though its used. I love my old workhorse the horizon II.

    Opticlabrat You are amazing I will do exactly what you said and I will keep you posted. Let me give credit where credit is due.

    You are the greatest......
    thanks
    again

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Review: Kappa Edger from Gerber Coburn
    By Sean in forum Optical Product Review Forum
    Replies: 80
    Last Post: 12-24-2008, 08:45 AM
  2. Need Bar Code Scanner For Essilor 900mx Edger
    By APV Optical in forum Optical Marketplace
    Replies: 2
    Last Post: 01-20-2007, 03:15 AM
  3. Gerber Professional Edger Question
    By eromitlab in forum General Optics and Eyecare Discussion Forum
    Replies: 6
    Last Post: 03-08-2005, 08:59 PM
  4. Topcon Edger and Service
    By DRCJD in forum General Optics and Eyecare Discussion Forum
    Replies: 5
    Last Post: 03-08-2003, 10:55 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •