Search:

Type: Posts; User: snowmonster; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.13 seconds.

  1. Replies
    9
    Views
    1,486

    Thanks for the help. I know everyone here...

    Thanks for the help.

    I know everyone here hates polycarbonate for drill mounts but we treat every hole and very rarely have stress crack issues. I would know since I’m the one that has to tear...
  2. Replies
    9
    Views
    1,486

    So this stuff at Optisource?

    So this stuff at Optisource?
  3. Replies
    9
    Views
    1,486

    Not really for the same purpose but maybe this...

    Not really for the same purpose but maybe this works?

    http://www.1-800-optisource.com/Poly-Edge-Glaze-8oz.aspx

    It should be a lot less expensive at least on a per ounce basis.
  4. Replies
    9
    Views
    1,486

    +1 on this for wanting a good replacement for...

    +1 on this for wanting a good replacement for Drill Seal without the words Trivex or Trilogy being mentioned. The stuff is fantastic.
  5. Replies
    24
    Views
    12,631

    I know this is an old topic but does the...

    I know this is an old topic but does the above-referenced cabinet really store 1,750 pair of stock lenses? Between finished single vision polycarb hard coat and finished single vision polycarb AR, I...
  6. Replies
    0
    Views
    1,296

    Santinelli ME1200 issue

    Hey all:

    My Santinelli ME1200 edger has been running great until just recently. I had an I/O board error a while back and then everything seemed okay but now the machine won’t make any of its...
  7. Replies
    9
    Views
    10,948

    Thank you - it's been a while and I learned a lot...

    Thank you - it's been a while and I learned a lot quickly here. Add in practice growth, teenage kids with activities and I'm just to busy now for a lot of stuff. Pretty good if I can go this long...
  8. Replies
    9
    Views
    10,948

    Reviving a really old thread. How do you block...

    Reviving a really old thread.

    How do you block a round seg with prism, especially if the lens has no cylinder to simply go by axis and decentration while blocking? I know how to normally block a...
  9. Replies
    6
    Views
    1,548

    I realize that I can tint that with a combination...

    I realize that I can tint that with a combination of grays and browns but I was just hoping to switch to a less orange brown tint color anyway. I was looking at BPI and about 5 different colors seem...
  10. Replies
    6
    Views
    1,548

    Help on Ray Ban tint color

    Looking for a tint that resembles the sort of grayish brown Ray Ban tint, not the G15 gray/green color. The tint we have seems to be more of an orange brown color.

    Here's what I'm looking for:
    ...
  11. Replies
    0
    Views
    1,966

    Looking for a Ray Ban 6213 drill chart?

    Haven't been around much lately but I'm looking for a Ray Ban 6213 drill chart for the 53 eye size. Can anyone help?

    Thanks in advance!
  12. Water. Coldness isn't generally an issue until...

    Water. Coldness isn't generally an issue until more crap gets built up inside chiller/pump/tubing and then I have to blow it out with compressed air.
  13. Chiller in the lab - how is yours hooked up?

    I've got a Elkay chiller in the lab that was set up by the group we bought it from. It's a recirculating (closed loop) system where a continuous pump sits inside of a small cooler with water in it. ...
  14. I have a Less Stress but I now have an ME1200...

    I have a Less Stress but I now have an ME1200 that almost everything gets done on automatically.
  15. Kazuo Kawasaki dismantling and drill hole size/location help?

    Hello! It's been a while...

    I've got a patient that needs new lenses in his Kazuo Kawasaki frame - MP631 in a 48 eye size.

    Anyone know the hole sizes and locations? I think I remember hearing...
  16. This is perfect - thanks! One more question - is...

    This is perfect - thanks! One more question - is it drilled straight back or perpendicular to the lens surface?
  17. Need help with Airlock hole/notch sizes and spacing

    I'm needing the hole/notch sizes and spacing for a Marchon Airlock frame - it's an AL800/53 in a 49 eye size.

    I called Marchon and all they did was send a pattern but nothing with any...
  18. Replies
    5
    Views
    4,046

    We clean the little hole and the window...

    We clean the little hole and the window occasionally but certainly not monthly. I'm half tempted to take it apart and see if there's anything obvious going on (since it's not under warranty).
  19. Replies
    5
    Views
    4,046

    I checked them and even switched them and it...

    I checked them and even switched them and it didn't seem to change anything. The test puff results in an "N.G." on the screen. I determined that to mean "not good."
  20. Replies
    5
    Views
    4,046

    Topcon CT-80 NCT tonometery help?

    We have a Topcon CT-80 NCT tonometer that just stopped blowing air yesterday. It makes a louder "chunk" sound now when you hit the button but doesn't blow any air.

    Has anyone out there run into...
  21. Replies
    18
    Views
    20,694

    I guess I just wanted to know the hole sizes (and...

    I guess I just wanted to know the hole sizes (and spacing if there are multiple holes or notches).
  22. Replies
    18
    Views
    20,694

    I know this is an old thread, but if you use...

    I know this is an old thread, but if you use Loctite or Krazy Glue, how do you disassemble the frame to put new lenses in without breaking the frame?

    Also, anyone have a drill chart for one of...
  23. Replies
    2
    Views
    1,415

    Thanks for the help. Is it located behind the...

    Thanks for the help. Is it located behind the front panel where all of the switches and buttons are?
  24. Replies
    2
    Views
    1,415

    Ultra Optics Mini II question

    I've got an Ultra Optics Mini II that works pretty well in general. The only problem I've got is when the arm swings over to the right to the coating bowl. It hits the stop point fairly hard and...
  25. Craig - the old ones (all plastic) are a 2.0 mm...

    Craig - the old ones (all plastic) are a 2.0 mm hole temporally but the important thing to know is that the hole spacing between those 2.0 mm holes was 2.5 mm instead of the usual 3.0 mm.

    If it's...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
OptiBoard is proudly sponsored by:
Younger Optics and Vision Equipment