Search:

Type: Posts; User: Chris Bowers; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.07 seconds.

  1. Replies
    3
    Views
    5,768

    This is called interference fringe. Caused by...

    This is called interference fringe. Caused by differences in lens index and coating index. Blue and red light are out of phase. Most notable under fluorescent lighting. It not noticeable by wearer.
    l
  2. Replies
    19
    Views
    7,668

    Neox G22 with a Chemistie clip as a round seg for...

    Neox G22 with a Chemistie clip as a round seg for easy removal
  3. Replies
    6
    Views
    2,923

    I think the Vision Council published something on...

    I think the Vision Council published something on this
  4. Replies
    7
    Views
    3,760

    You might want to check your water temperature....

    You might want to check your water temperature. 65 degrees fis best. If too cold and you will get swirls
  5. Glare by definition is light entering the eye at...

    Glare by definition is light entering the eye at an unusable angle. AR coating will not change or inhibit that light.
  6. Replies
    5
    Views
    2,705

    Go into calibration and select option # 5 “off...

    Go into calibration and select option # 5 “off sets”
  7. Replies
    17
    Views
    12,020

    Sounds like your water is too cold. Best practice...

    Sounds like your water is too cold. Best practice is to usewater at 65 F. Direct water in Saint Paul is going to be around 56.5 degrees. Useyour water in a recycled container and cool from ambient...
  8. Replies
    7
    Views
    5,373

    You should know that these were also indexed. A...

    You should know that these were also indexed. A critcal componant for calculations
  9. Red dye takes up fastest at 185 f and yellow at...

    Red dye takes up fastest at 185 f and yellow at 210 f. Best temp for even take up is 205 f if your altitude allows
  10. Replies
    8
    Views
    4,298

    I think many times when we speak of ANSI we do...

    I think many times when we speak of ANSI we do not cover 1.2 purpose. There are two very smart people on this board that help with the creation and maintence of ANSI perhaps we can start a dicusion...
  11. Replies
    13
    Views
    5,478

    Try viewing under a polariscope

    Try viewing under a polariscope
  12. Replies
    9
    Views
    4,245

    Swim Goggles, Diving mask, moisture chamber ...

    Swim Goggles, Diving mask, moisture chamber clear wraps around???
  13. Thread: Pls 540

    by Chris Bowers
    Replies
    5
    Views
    3,060

    Thanks Robert I might have to go down this road.

    Thanks Robert I might have to go down this road.
  14. Thread: Pls 540

    by Chris Bowers
    Replies
    5
    Views
    3,060

    Thanks I do have something coming from them. I...

    Thanks I do have something coming from them. I have never been able to get the "brightness" of the original
  15. Thread: Pls 540

    by Chris Bowers
    Replies
    5
    Views
    3,060

    Pls 540

    Hi,are there any sources for the Younger PLS 540 lens out there?

    Thanks,

    Chris
  16. Replies
    17
    Views
    8,432

    If you had a +15 in an 80mm blank I guessing it...

    If you had a +15 in an 80mm blank I guessing it would have to be asheric. I think you would lose your fine point focus.
    Indepedant of power the total heat is a factor of lens size. Power determines...
  17. Replies
    17
    Views
    8,432

    parabolic dish might be a better aplication, the...

    parabolic dish might be a better aplication, the power of a lens is constrain by size as well as dioptic power
  18. Replies
    18
    Views
    8,054

    Simple green is also a good product.

    Simple green is also a good product.
  19. Replies
    4
    Views
    2,830

    Dac

    Dac?
  20. plano not parallel

    RT that depend on the lens index
  21. We need to be careful when stating the exactness...

    We need to be careful when stating the exactness of an older manual lensometers. Consider the following Rx… +2.00 – 1.00 @ 90. Somewhere on this lens should exist a meridian with a power of +1.50 and...
  22. Replies
    78
    Views
    39,465

    probally surface related

    I’ve made a lot of poly lenses and with many different processes. About six years ago we started a few of our labs in a cut to polish surface method. About a year into this I noticed that these labs...
  23. .25 bo prism reality check

    I’m confused. Doesn’t the image (following) reverse from base to apex when powers change between minus and plus?
    How do we apply Barry’s rule to a Plano powered lens with non parallel surfaces?
    As...
  24. Replies
    9
    Views
    4,067

    Hope this helps

    icare,

    I hope they call before subbing. I've attached a list of availabilities but they do change often.

    Chris
  25. Replies
    42
    Views
    15,280

    Give the information

    Barry,

    If you give us BVD, Wrap and panto we can applly on an Rx basis. The more info the better we can optomize these lenses.

    Chris
Results 1 to 25 of 66
Page 1 of 3 1 2 3