Search:

Type: Posts; User: Mike Fretto; Keyword(s):

Page 1 of 10 1 2 3 4

Search: Search took 0.12 seconds.

  1. Replies
    7
    Views
    3,878

    A/R defect detection

    Without trashing any one particular manufacturer we occasionally have problems with stock A/R coated lenses crazing in either the blocking, edging, or deblocking process. Usually undetectable to us...
  2. Thread: Weco 3D+

    by Mike Fretto
    Replies
    0
    Views
    2,567

    Weco 3D+

    We are looking for a current loop card to run our Weco 3D+ edger using Innovations and Labzilla software. Needing a back up edger and we have the Weco sitting on the counter.
  3. Replies
    10
    Views
    3,917

    Would'nt Optimizing the RX help. If I plug the rx...

    Would'nt Optimizing the RX help. If I plug the rx into Darryl's OptiCampus calculator I get the following results.

    Assuming 9 deg tilt and 15 deg wrap
    OD -2.50 -2.25 x155 becomes -2.35...
  4. Replies
    19
    Views
    6,100

    Are the lenses cribbed to the smallest diameter...

    Are the lenses cribbed to the smallest diameter needed to cut out. Ive started attaching shapes to all my uncut/AR orders otherwise we grind inhouse and crib to smallest diameter needed. We also...
  5. Replies
    7
    Views
    5,205

    We had a similar problem after replacing our...

    We had a similar problem after replacing our monitor. We used an old monitor we had laying around that would hook up to the SGX. Unfortunately it was considerably heavier than the little Coburn...
  6. Replies
    15
    Views
    5,726

    Weve done some of the Trivex product with great...

    Weve done some of the Trivex product with great success the problem is the certain insurance plans that give the poly product to their members for nothing. Im not sure Ive ever heard why Transitions...
  7. Replies
    15
    Views
    5,726

    As I said earlier I dont want to slam any...

    As I said earlier I dont want to slam any specific company but thats going to be hard to avoid with this particular combination. Im looking for some verification that this is a real problem or are we...
  8. Replies
    15
    Views
    5,726

    There is only one poly st28 photo. out there and...

    There is only one poly st28 photo. out there and it is laminated.
  9. Replies
    15
    Views
    5,726

    Poly Photochromic Problems

    Were having problems within our practice with the above mentioned product delaminating in single vision and st 7x28 and 28 and 35's I don't want to be specific about Vendors but the above...
  10. Replies
    6,076
    Views
    1,261,214

    Yes we are working

    Yes we are working
  11. Replies
    12
    Views
    5,765

    Western Carolina...

    Western Carolina http://www.wcoinc.com/site_001.htm

    Also POL Optical Labs I couldnt find a website???
  12. Aspirin and something good to wash them...

    Aspirin and something good to wash them down:banghead:
  13. Replies
    6
    Views
    2,719

    David Im somewhat limited to vendors we have...

    David
    Im somewhat limited to vendors we have already used. We dont have accounts with the two you mentioned but we may be able to go through one of the wholesale labs we use.
  14. Replies
    6
    Views
    2,719

    Looking for Lenses

    We are looking for a source for finished sv CR39 tinted Planos in either grey or brown. Apparently were going to be cranking out some cheap sunglasses for a contact lens promo offer and it would be...
  15. Replies
    21
    Views
    9,382

    The only down side to our setup is cribbing takes...

    The only down side to our setup is cribbing takes forever. As little work as we do it isnt really an issue as far as time. Crib Reduction is 25 and feed is 200 any more or faster and they seem to...
  16. Replies
    21
    Views
    9,382

    You said your water is chilled Im assuming your...

    You said your water is chilled Im assuming your running some kind of filtered tank. If so is the filter and water changed frequently, are the swirls consistent or occasional, any particular spot on...
  17. Replies
    4
    Views
    2,495

    Hard to work with Metal Frames

    Is it just me or is there a slew of frames out there right now that are deigned by people with no regard to we that have to work with them. One design in particular that drives us crazy is a metal...
  18. I played with their site briefly, selected a...

    I played with their site briefly, selected a frame, and tried unsuccessfully to pick a Transitions high index progressive. After watching a short video teaching me how to measure pd with what...
  19. Replies
    1
    Views
    2,601

    SGX Poly vs. Trivex

    Ok after a previous thread on poly cracking many have suggested going with Trivex as an alternative. We've avoided Trivex for one main reason the material was not a choice in our retail program, and...
  20. Replies
    32
    Views
    11,915

    We grind lenses for 6 offices if I could get the...

    We grind lenses for 6 offices if I could get the dispensers in 6 offices to quit selling poly I would be a happy man, but that aint gonna happin anytime soon.
  21. Replies
    32
    Views
    11,915

    Chris, Im not sure I explained well, I have to...

    Chris, Im not sure I explained well, I have to place my orders through my home office. They wont allow any international orders any more. So I need a source in the US to order through, Ive talked to...
  22. Replies
    32
    Views
    11,915

    Chris I was hoping to hear from you is there a...

    Chris I was hoping to hear from you is there a distributor in the States for Drill Seal we have been using it for several years, now were told our company will no longer allow international orders.
  23. Replies
    32
    Views
    11,915

    Albednar the lenses arent exposed to harmful...

    Albednar the lenses arent exposed to harmful chemicals while in our possession, what happens to them once the patient gets their grubby little hands on them who knows. I seem to remember in the early...
  24. Replies
    32
    Views
    11,915

    These cracked lenses are returning from our...

    These cracked lenses are returning from our outlying offices after dispensing. Still waiting to hear from someone who may have heard about the Blue-Ray disk thing . I guess I dreamed it :-)
  25. Replies
    32
    Views
    11,915

    We polish the edges on all our rimless jobs weve...

    We polish the edges on all our rimless jobs weve felt it just looks nicer. We understand the problems this can cause with reflections. Weve never tried grooving wet on poly that may help clean it up...
Results 1 to 25 of 235
Page 1 of 10 1 2 3 4