Announcement

Collapse
No announcement yet.

Wireless Network Problem

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Wireless Network Problem

    I just set up a wireless router (Netgear WMB521) and got it working. Two of the PCs are still using an ethernet cable while the third one is using a D-Link PCI card (router and card are 802.11b).

    Everything is working fine except for one thing. Although the D-Link PC has the full Internet connection, I can't get it to recognize the other PCs on the network, nor can those PCs access it. I ran the Home Networking Wizard on the D-Link PC but when it was done, not only did the local network not work, but it broke the Internet connection. Consequently I removed the bridge that was causing this problem and this restored the Internet.

    Any advice on how to get the D-Link PC to be part of this local network? I have enabled file sharing and assigned it to the same workgroup, but its still not working.

    OptiBoard Administrator
    ----
    OptiBoard has been proudly serving the Eyecare Community since 1995.

    #2
    Originally posted by Steve Machol
    I just set up a wireless router (Netgear WMB521) and got it working. Two of the PCs are still using an ethernet cable while the third one is using a D-Link PCI card (router and card are 802.11b).

    Everything is working fine except for one thing. Although the D-Link PC has the full Internet connection, I can't get it to recognize the other PCs on the network, nor can those PCs access it. I ran the Home Networking Wizard on the D-Link PC but when it was done, not only did the local network not work, but it broke the Internet connection. Consequently I removed the bridge that was causing this problem and this restored the Internet.

    Any advice on how to get the D-Link PC to be part of this local network? I have enabled file sharing and assigned it to the same workgroup, but its still not working.
    Are all the PC's using DHCP to get their IP addresses? If not, they may be on different subnets (esp. if the two wired boxes are getting autoconfig adresses).

    Comment


      #3
      Steve,

      For starter's i would make sure that the the number of DHCP user's are correct.And then check to make sure that the numbers are assigned automatically. 2nd i would check to see if the router is set to open or shared key if wep is enabled. 3rd check to see if the IEEE 802.1x Authentication is enabled or disabled for both parties. 4 th check the MAC filter address . 5th Is the Domain name the same?

      Comment


        #4
        It looks like it may have been a firewall issue. I think I've got it resolved now. Thanks!

        OptiBoard Administrator
        ----
        OptiBoard has been proudly serving the Eyecare Community since 1995.

        Comment


          #5
          Originally posted by Steve Machol
          It looks like it may have been a firewall issue. I think I've got it resolved now. Thanks!
          Was the problem with the firewall in the router or in Xp. I'll go on a hunch and say it had to do with Xp. Either that or other installed software i.e. Nortons, Zone Alarm..etc.

          Comment


            #6
            I configured the Norton firewall to allow connections from the local network (192.168.0.x) and that seems to have fixed it so far. I don't use the firewall in XP Home.

            OptiBoard Administrator
            ----
            OptiBoard has been proudly serving the Eyecare Community since 1995.

            Comment


              #7
              Spoke too soon. As soon as I rebooted I lost all connections - Internet and local network. I disabled all firewalls yet I still can't get reconnected.

              Is there a source available somewhere that provides a simple explanation of how to get a wireless connection working? I mistakenly assumed tht Win XP would be more advanced in this regard but I was wrong.

              OptiBoard Administrator
              ----
              OptiBoard has been proudly serving the Eyecare Community since 1995.

              Comment


                #8
                The NetGear web-site was useful (for me) when I was hooking up my Wireless Router. I was only working through the WEP stuff, since I don't need to do sharing. So I'm not sure what they have on that part.
                J. R. Smith

                Comment


                  #9
                  Steve,

                  There are some significant differences between XP Home Edition and XP Professional when it comes to networking. Also you can expect issues with a heterogenious network. Keep cranking and you may iron out all of your problems.

                  Look at this as a learning experience as it certainly is. Working through this challange will give you a wanm, fuzzy feeling. Failure and you may end up with your head in the oven. In any case, try to document everything you do (IP addresses, etc.) because chances are pretty good that you will have to do it again. And, again.

                  Peace,

                  Dick
                  Dick

                  www.aerovisiontech.com

                  Comment


                    #10
                    Steve, do I understand correct that you have 2 routers on the same network?

                    If so, one should definately have the DNS turned off. I would even replace one of the routers with a hub or switch.

                    Rick Strong

                    Comment


                      #11
                      XP Home.......

                      Originally posted by Steve Machol
                      I configured the Norton firewall to allow connections from the local network (192.168.0.x) and that seems to have fixed it so far. I don't use the firewall in XP Home.
                      Steve,
                      Sorry to be the bearer of bad news but XP Home does not support TCP/IP routing or DNS. In short, you will be able to surf the net from the computers attached to the router, but will not be able to network the computers for file or print sharing.:(

                      Comment


                        #12
                        Actually I have one router which includes both ethernet connection and wireless. Also I have fixed the problem.

                        What I had to do was disable the encryption on the wireless network. This allowed the one PC with the wireless card to connect to both the Internet and the shared files on the other PCs on the network. I then re-established the encryption, only this time I used 64-bit instead of 128-bit. I generated a new encryption key, put this into the wireless PC and the connection still held. I rebooted a few times and everything is working fine.

                        Since this is Marlena's new PC, I downloaded all of her personal files (about 200MB) from her existing PC to the new wireless one. It worked very smoothly. :)

                        My next task is to transfer her Outlook Express emails and settings from the old PC to the new one. Unfortunately Microsoft makes this very difficult to do.

                        OptiBoard Administrator
                        ----
                        OptiBoard has been proudly serving the Eyecare Community since 1995.

                        Comment


                          #13
                          Congrat's....glad to see it work out. The only ? i would have is why does it work at 64 bit Wep and not 128. The most common mistake with 128 is that when the key is generated not all of the values are displayed.You have to right arrow over to see the last three or four values.Unlike 64 bit ...the box for 128 appears full but theres more.

                          Comment


                            #14
                            It did work sometimes with 128-bit so I'm sure the key was fine. However it would stop working after I rebooted and I could not get it to work again.

                            OptiBoard Administrator
                            ----
                            OptiBoard has been proudly serving the Eyecare Community since 1995.

                            Comment


                              #15
                              Originally posted by Steve Machol
                              It did work sometimes with 128-bit so I'm sure the key was fine. However it would stop working after I rebooted and I could not get it to work again.
                              Either way :) ...........Glad to see things are up and running ;) .

                              Comment

                              Working...
                              X