Results 1 to 4 of 4

Thread: Reading level for Slab off prism on progressive

  1. #1
    OptiBoardaholic
    Join Date
    Jun 2006
    Location
    Panama
    Occupation
    Optometrist
    Posts
    235

    Reading level for Slab off prism on progressive

    On most flattop bifocal jobs I use 10mm as reading level on the slab off prism calculator with excellent results.
    How is the reading level calculated for progressive?
    On this progressive lens the MRP is 4mm below the fitting cross and there are 16 mm from fitting cross to the center of the reading part of the progressive lens. This is a Freeform progressive.
    Which should be the Reading level on this job? 16mm or (16-4)=12mm.

  2. #2
    One eye sees, the other feels OptiBoard Silver Supporter
    Join Date
    Jul 2002
    Location
    Wauwatosa Wi
    Occupation
    Dispensing Optician
    Posts
    5,458
    In this case use 12mm to determine the Vertical Imbalance at near, if the reading depth below the Prism Reference Point is actually 12mm. There will be VI on the distance gaze, maybe enough to be a concern. If true, one might introduce prism to cancel, recalculating the near slab value to compensate.

    In some cases when the anisometropia introduces a fairly low value of VI, one might use a PAL with more "drop" (Zeiss uses 6mm), reducing the VI at near, eliminating the need for a slab.

    Make sure that the PAL near zone developes 100% of the add about 3mm to 5mm above the reading level, the latter determined by placing a horizontal line bisecting the pupil when the client is reading, confirming with the "mirror method" or by sitting on the floor.

    Hope this helps,

    Robert Martellaro
    Science is a way of trying not to fool yourself. - Richard P. Feynman

    Experience is the hardest teacher. She gives the test before the lesson.



  3. #3
    Master OptiBoarder optical24/7's Avatar
    Join Date
    May 2006
    Location
    Down on the Farm
    Occupation
    Dispensing Optician
    Posts
    5,809
    Pal's and slab go well together like oil and water. Clients are usually disappointed. They now get a line or blurr zone in one eye, even with FF's. They can still have diplopia in given area's along the umbilic. I highly recommend they consider a ft bi or tri.

    If you still wish to proceed, figure the power at 90. Don't use prism thinning. Put OC's 1-2mm's below pupil, then figure how many mm's below them you'll induce 1D of imbalance. Put your slab line there. Make sure there is adequate room left for near vision.

    Also make sure this patient uses both eyes at near before you even go with a slab. If they have gone with this imbalance for very long in Pal's, they probably have developed a monocular near task style of use.

  4. #4
    OptiBoardaholic
    Join Date
    Jun 2006
    Location
    Panama
    Occupation
    Optometrist
    Posts
    235
    Thanks for the explanations

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Calculating Slab-Off: Ideal Way to Find Reading Depth?
    By Chad Sobodash in forum General Optics and Eyecare Discussion Forum
    Replies: 14
    Last Post: 04-22-2014, 07:34 AM
  2. Slab off AND prism
    By Mary in forum General Optics and Eyecare Discussion Forum
    Replies: 8
    Last Post: 10-20-2012, 07:55 AM
  3. Prism only for the reading portion of a progressive
    By jonah in forum General Optics and Eyecare Discussion Forum
    Replies: 11
    Last Post: 06-04-2012, 05:51 PM
  4. Slab-off Prism
    By Neophyte Optician in forum Ophthalmic Optics
    Replies: 11
    Last Post: 04-24-2006, 01:29 AM
  5. How does everyone measure reading level for slabs?
    By William Walker in forum General Optics and Eyecare Discussion Forum
    Replies: 1
    Last Post: 06-08-2005, 12:15 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •