Search:

Type: Posts; User: Thumbs; Keyword(s):

Page 1 of 10 1 2 3 4

Search: Search took 0.09 seconds.

  1. The message barcode 39 only means that the...

    The message barcode 39 only means that the barcode reader is initialized and working. Most operators never notice it is always on until they have a problem. The error code A75 c22.4/601 is Error...
  2. Replies
    3
    Views
    1,913

    I would look at the Delta 200 system from Essilor...

    I would look at the Delta 200 system from Essilor Instruments. https://www.essilorinstrumentsusa.com/products/lens-finishing-systems/delta-100-200-300/
  3. No you can not. The Delta 200 can be connected to...

    No you can not. The Delta 200 can be connected to the Tess tracer and is being sold with it.
  4. Replies
    7
    Views
    4,819

    Essilor Instruments Manufacturing

    To confirm, all of Essilor branded edging systems have always and currently are manufactured in France where their current location is about 2 hours outside of Paris in a small town called Ligney....
  5. That is unfortunate that your part time tech has...

    That is unfortunate that your part time tech has experienced what you state. I found the Mr Orange to be a lot faster than the ME -1200 by up to 50% when it was programmed correctly. The drilling...
  6. Not that I question Coburn's tech about a blown...

    Not that I question Coburn's tech about a blown port driver but if you know of someone near you with a N95 kappa you should test your board on there machine. If you want to send to me I can test it...
  7. Replies
    10
    Views
    6,989

    If the lens is off axis but the block did not...

    If the lens is off axis but the block did not slip check the wiring harness connection at the lens drive motor. If the harness is being held to the motor with a Velcro strap and a wire tie around it,...
  8. Have you looked at Essilor Instruments Mr Blue or...

    Have you looked at Essilor Instruments Mr Blue or Mr Orange? Features include milling, drilling, step bevel, remote maintenance, software updates for life, chemistries software at no charge, job...
  9. You could also try calling Essilor Instruments...

    You could also try calling Essilor Instruments USA at 1-855-393-4647 for support. The Triumph edger/tracer where manufactured by Essilor for GerberCoburn back in the 90's. Currently National...
  10. Replies
    22
    Views
    10,583

    I know the owner personally, an independent...

    I know the owner personally, an independent Massachusetts licensed optician who knows what the customers are looking for. He goes to the extreme to keep his customers satisfied and very easy to do...
  11. 10 years old and no service from the only...

    10 years old and no service from the only distributor in the US? Does Santinelli disclose this at the time of sale? Never trusted their sales pitches and this confirms I made the right decision years...
  12. Thread: Essilor Edgers

    by Thumbs
    Replies
    9
    Views
    8,174

    GerberCoburn was sold over a year ago and their...

    GerberCoburn was sold over a year ago and their new name is Coburn Technologies. At that time, they lost the distribution for Essilor edgers and Essilor started to distribute directly under the name...
  13. Replies
    75
    Views
    38,206

    You should check out the Essilor Mr Blue and Mr...

    You should check out the Essilor Mr Blue and Mr Orange? They both can drill, chamfer, shelf bevel for high base and groove. Mr Blue has a milling bit to eliminate slippage/crazing of AR lenses while...
  14. Replies
    27
    Views
    19,818

    [QUOTE=bhess25;401905]i spoke with the rep @ east...

    [QUOTE=bhess25;401905]i spoke with the rep @ east west...mr.blue is 61k...unless you get the mye touch feature then its cloer to 69k!![/QUOTE

    The price that you are quoting is not close to what...
  15. Replies
    4
    Views
    2,253

    The Essilor Rainyl groover is what I was thinking...

    The Essilor Rainyl groover is what I was thinking of as the only manual groover available today.
    http://www.ophthalworld.de/cosmoshop/pix/a/n/1313579791-15128.jpg
  16. Replies
    4
    Views
    2,253

    You can purchase a new one from Essilor...

    You can purchase a new one from Essilor Instruments @ 1-855-ez-finish
  17. Thread: New Edger Time

    by Thumbs
    Replies
    38
    Views
    14,909

    So, I stand by my statement, calling Santinelli,...

    So, I stand by my statement, calling Santinelli, "huge" and Coburn "small" is all relative and making assumptions on the level of service that they may, or may not, be able to provide based on size...
  18. Thread: New Edger Time

    by Thumbs
    Replies
    38
    Views
    14,909

    "I have no idea where you get this information...

    "I have no idea where you get this information from but wherever it is you may seriously want to find another source. Or take the time to do a little research."


    Here are some facts about...
  19. Replies
    6
    Views
    3,105

    Possible communication cable/connection issue?...

    Possible communication cable/connection issue? Try using another communication port and/or cable. SGX will read job not found if there is no communication to the Innovations program.
  20. Replies
    2
    Views
    2,669

    You cannot retrieve the trace data from the 7070...

    You cannot retrieve the trace data from the 7070 for exporting.
  21. Replies
    1
    Views
    2,150

    the drill on the smartdrill that I do use anymore...

    the drill on the smartdrill that I do use anymore says the manufacturer is Proxxon and I believe the model is Micromot IB/E
  22. Replies
    3
    Views
    3,095

    This machine is worth whatever you would be...

    This machine is worth whatever you would be willing to pay for it yourself. Remembering that you would be purchasing it with no training, installation, warranty, the trust from the seller, etc..
  23. Thread: edgers

    by Thumbs
    Replies
    12
    Views
    7,235

    To update the total confusion of Gamma vs Kappa...

    To update the total confusion of Gamma vs Kappa from Essilor, as of Essilor taking over the distribution of edgers in the US from GerberCoburn, they have also changed the names around.
    They are as...
  24. Replies
    10
    Views
    5,566

    Thanks for the info. What does a rebuilt and new...

    Thanks for the info. What does a rebuilt and new Gamma tracing table cost these days?
  25. Thread: Briot VS Weco

    by Thumbs
    Replies
    16
    Views
    11,500

    I agree that WECO edgers are workhorses and worth...

    I agree that WECO edgers are workhorses and worth the price. Unfortunately, here in the states, WECO is all but non-existent. They can't keep a distributor for more than a year or two, currently AIT...
Results 1 to 25 of 235
Page 1 of 10 1 2 3 4