Search:

Type: Posts; User: Dantech; Keyword(s):

Search: Search took 0.06 seconds.

  1. Replies
    1
    Views
    5,743

    Pitting is always more noticeable on Cr39 polar,...

    Pitting is always more noticeable on Cr39 polar, it is probably happening on clear and trans you just aren't noticing it. First thing you need to focus on is water flow. If any of your milling or...
  2. Replies
    12
    Views
    11,799

    What i meant is, you can take the air and water...

    What i meant is, you can take the air and water out of the equation by running 99% isopropyl alcohol instead of water and disconnecting the air jet. However it seems your lamp may be getting stuck...
  3. Replies
    12
    Views
    11,799

    You should not adjust those knobs without a laser...

    You should not adjust those knobs without a laser tachometer, adjusting changes the speeds at which the spindles spin during the cycle. ultra optics will rent you a tachometer for more than they cost...
  4. Replies
    17
    Views
    15,957

    We run v 2.3, with this update you no longer have...

    We run v 2.3, with this update you no longer have to use the calculate button unless your making changes, but the biggest benefit is the fact that it leaves a small bump in the center of poly lenses...
  5. Replies
    17
    Views
    15,957

    We called them nipples, you can increase your...

    We called them nipples, you can increase your fine time to eliminate these. Or the option i would recommend is updating your software to the new version it compensates to eliminate this problem and...
  6. Replies
    69
    Views
    47,496

    I'm looking for a wax Eclipse blocker. Email ...

    I'm looking for a wax Eclipse blocker.

    Email Dan@acuitylabs.com
  7. Replies
    33
    Views
    23,274

    With the step one when i install new elevator...

    With the step one when i install new elevator plates i always take a rough fining pad and sand the steal pin a little bit otherwise our blocks don't always seat correctly. Other things to look at 1....
  8. Thread: Scratches!!!

    by Dantech
    Replies
    27
    Views
    15,217

    Are suggesting to wash the lenses before...

    Are suggesting to wash the lenses before deblocking after being edged? After surfacing a lens we do rinse under cold water after deblocking and removing tape.
  9. Thread: Scratches!!!

    by Dantech
    Replies
    27
    Views
    15,217

    We do not edge glass, we run all dry cut machines...

    We do not edge glass, we run all dry cut machines that use non recyclable coolant to polish.
  10. Thread: Scratches!!!

    by Dantech
    Replies
    27
    Views
    15,217

    Thanks guys, Georg i am using a closed loop...

    Thanks guys, Georg i am using a closed loop polish system on each polisher with chiller coils in the reservoir i have a couple ideas on incorporating this filter but it may be a little more...
  11. Thread: Scratches!!!

    by Dantech
    Replies
    27
    Views
    15,217

    That's one i haven't heard. What do you use to...

    That's one i haven't heard. What do you use to filter it?
  12. Thread: Scratches!!!

    by Dantech
    Replies
    27
    Views
    15,217

    Umm?

    Umm?
  13. Thread: Scratches!!!

    by Dantech
    Replies
    27
    Views
    15,217

    Scratches!!!

    Lately we have been having issues with a large amount of scratches skyrocketing our breakage percentage. We have tried many cloths and have finally settled on disposables which seem to have the best...
  14. Replies
    4
    Views
    9,396

    Sounds like the clarity however you can manually...

    Sounds like the clarity however you can manually align progressives. Biggest problem is that it is incredibly slow and can take an hour to calibrate our own way due to it not calibrating itself...
  15. Replies
    4
    Views
    9,396

    We have a clarity it seems to be a work in...

    We have a clarity it seems to be a work in progress still, we dont shut it off EVER due to calibration nightmares. Have not used the other brands but with accurate techs a lensometer and a 3b will...
  16. Replies
    17
    Views
    15,957

    I do all of the maintenance and repair on all of...

    I do all of the maintenance and repair on all of our machines we don't use the unity max we use a gerber eclipse for blocking but we do use Optek surfacing equipment. We have 3 contour max generators...
  17. Replies
    3
    Views
    5,906

    We use 3 of the 7e or hlp edgers two to groove...

    We use 3 of the 7e or hlp edgers two to groove and one for drill mounts along with three 6es. This has significantly reduced our breakage although it is a slightly slower process. The 6es however do...
  18. Replies
    3
    Views
    4,540

    Innovations should support most oma compliant...

    Innovations should support most oma compliant machines if you are using a serial cable you will sometimes need to change the wiring configuration in some cases a null modem will suffice. Just make...
Results 1 to 18 of 18