Permanent Anti-Fog Coating ............
I came up with a new coating that I would a few OptiBoard Members to try out. Any volunteers please contact me at oms_optical@yahoo.com , but please mark it on subject: line so it wont go into the trash folder.
Anti-fog coatings are known to get tired after a while and will not work anymore.
My new coating can be renewed by heating the lenses in microwave for 2 minutes, and they will work again like new.
(Do not heat the frame along with lenses.............just tried it and everything went up in flames......so remove lenses from frame)
You can check it out on my website at: http://optochemicals.com/paf_antifog.htm
Is this the same stuff?........................
Quote:
Originally Posted by
DragonLensmanWV
Atually it is not the same stuff without me knowing the Opticote stuff.
Quote:
They advertise it as a :
Thermal cure process with dip hard coat primer and Fog Free coating, 2 day turnaround
TINTS cannot be coated at this time
My stuff is a humidity cure copolymer you can apply it on any surface you want and do it in about 5 minutes. The only condition is that your lens or coatings can take the heat in the microwave for 2 minutes and AR coatings can not be done as it would be covered by the coating and become ineffective.
Waiting for some results....................
I am still looking for any results from the ones that were going to test the product
anti fog......................
Quote:
Originally Posted by
IndianaOD
I tried it on 2 pairs so far. I would say it cut the fogging down perhaps 50%. Though I don't have a source of steam in the office so holding it over a cup of really hot water might not have cured it properly.
The wetting is enough as you describe, but you do not say if you even did the next step, which was to wet the lenses again and then place into a microwave oven and heat at full strenght for 1 minute, only then the coating becomes 100% anti fog.
The question is really, once properly done how long do they stay anti fog, 2month or 4 month. Then they can be wetted again and placed in a microwave for 1 minute and they work again as before.
Finally some answer..............................
Got This in my e-mail today
Quote:
Originally Posted by gunner05
Hey Chris, you sent us some anti fog solutions to try out a few months ago and I just wanted to give you a heads up. We tried it with four patients, and two have been extremely impressed with it. The other two fell off the face of the planet, it seems.
Actually it just happened that Canadas largest Safety Optical has started to supply it on lenses.
information about Anti fog coatings included in AR coatings..........................
Quote:
Originally Posted by
fcl
I´m looking for information about Anti fog coatingsincluded in AR coatings, but I´m not found it. Anybody knows if it´s possibleadd this property in an AR Coating?
I make AR coatings withsuperhidrophobic in High vacuum systems and I would like to add this propertyin our process.
The product you are looking for does exist and is available as a concentratefor applicationm in the vacuum chamber or as a water based solution for an easydip coat operation as well as a by hand application that has renewable featureswhen the hydrophillic qualities are getting fatigued.
Look it up on my website at: http://optochemicals.com/crystalclear.htm
Where can i buy it?! ...........................
Quote:
Originally Posted by
Den
Has your project got any advancement?
Did i understand right: by just putting a lens into your solution it acquires anti-fog properties?
For me it sounds amazing...
Wher can i buy it?!
Have you got any such solutions to renew the AR?
You can find it on my website at http://optochemicals.com
and in particular the page is -------------->
you would create a wavy surface .................................
Quote:
Originally Posted by
erichwmack
Off the topic slightly but Chris have you ever looked into developing a hardcoat that can self heal and fill-in moderate scratches on lenses by microwave or oven heating?
If it could be done, you would get another problem ......................
Scratches have removed some of the coating materials and by melting the coating back together with heat you would create a wavy surface which is a no no, on Rx lenses..
Defective AR can not be fixed........................................
Quote:
Originally Posted by
Den
Have you got any such solutions to renew the AR?
Defective AR can not be fixed.........however we have a stripper that is not dangerous that will remove it in seconds,
and then you can recoat or leave as is.
Here it is : The website is .....................................
Quote:
Originally Posted by
Den
you blow my mind with that info...
Is there any information about that on your site? I'll be very thankful for the link.
Here it is : http://optochemicals.com/ ......and the direct link is
http://optochemicals.com/products/info_ar_stripper.htm